If you are playing audio via AUX cable, make sure the speaker Is ln AUX IN mode, etc. Make sure the speaker is set to the same source as your audio device.Unplug the AC POWER cord, then plug it back in.Reset the speaker by turning the power OFF, and then back ON.Make sure AC POWER cord is fully inserted into the unit.Ensure the speaker is not in STANDBY MODE.Verify that the POWER switch is fully turned to the ON position.Press the BUTTON on the grip area to adjust the carry handle to a comfortable length.Pull the telescoping carry hand le UP and away from the speaker to extend it.Standby mode can be manually enabled in any mode. The speaker will automatically enter standby mode after -15 minutes of Inactivity or lack of connection. Press any button or turn the VOLUME knob to wake the speaker up from standby.LED Power LED indicators will turn shut on.Press and hold the VOLUME knob for -3 seconds to put the speaker in standby mode.Audio playback will transmit through the Rockin’ Roller 270 and the second speaker simultaneously. Press the NUMBER KEY while In radio mode to go to the corresponding SAVED station.Ĭonnect a second speaker to the Rockin’ Roller 270 via the LINE OUT port with a standard 3.5 mm jack. The saves LED station display (P-1wi, ll P-2, confirm etc.) Save the current radio station by pressing and holding one of the NUMBER BUTIONS (1-5). Press a NUMBER BUTTON (1-5) to change the speaker’s equalizer settings.The menu will revert to the audio source mode after 5 seconds of being idle.Įqualizer Presets (Bluetooth/AUX-IN ONLY) Pressing the BASS/TREBLE button a third time will revert to the audio source mode. Turn the VOLUME knob clockwise to increase or counter-clockwise to decrease the bass/treble levels (-06 to 06}.Press the BASS/TREBLE button TWICE to enter treble level mode. Press the BASS/TREBLE button ONCE to enter bass level mode.To disconnect a speaker, press the TWS button. Press and hold the TWS pairing button to Transfer speaker for 3 s to activate TWS pairing.
#Monster powercard manual Bluetooth
Leave the second speaker in BLUETOOTH mode without connecting to a device. Place two Rockin’ Roller 270 speakers within 1 O feet of each other.Ĭonnect your music device to one of the speakers via BLUETOOTH. Wirelessly connect two Roclcin’ Roller 270 speakers together. Press and hold the ARROW buttons to scan for a station. Press the ARROW buttons to change radio frequency. Speaker will make audible and visual LED display confirmations. Press the SOURCE button to change the speaker to FM RADIO. Speaker will make audible and visual LED display confirmation. The speaker will automatically change to AUX mode. Turn GAIN and ECHO control knobs clockwise to increase their effect, and counter-clockwise to decrease their effect.Įach 1/4 Inch port has Its own GAIN and ECHO knobs that can be adjusted independently.ĭevices plugged Into the 114 Inch ports will transmit audio playback in all modastsourcas.Ĭonnect a music device to the AUX IN port with a standard 3.5 mm jack. The device(s) will automatically transmit audio playback through the speaker in the current mode. microphone, or another device to the MIC/GUITAR or MIC port(s) with a standard Y4 inch jack. Moving devices outside this range may cause disruption or signal loss.ġ/4 Guitar/Mic Inputs & Gain/’Echo ControlsĬonnect an instrument. The speaker will make audible confirmation and the Bluetooth icon will stop flashing.ģ0 feet max connection range after paired. press and hold the BLUETOOTH button to manually enter pairing mode.ģ Select “MONSTER RR270 on your mobile device to pair with the speaker. The bluetooth icon will flash in pairing mode.
The speaker will make audible and visual LED confirmation. The speaker will automatically enter pairing mode. Press the BLUETOOTH button to set the speaker to Bluetooth mode. Make sure Bluetooth Is enabled on your mobile device. Place your mobile device within 3 feet of the speaker. USB port is for charging ONLY -they will not make audio connections. Flip the switch DOWN to turn OFF the speaker.Ĭonnect device to the speaker via the 5V/2.1AUSBport to charge device from the speaker’s internal battery.The speaker will connect to the last selected source.) Flip the switch UP to tum ON the speaker.Connect the INPUT POWER port to an external power source using the Included power cord.
0 kommentar(er)
